:: CLAUSING COLHESTER GEARED HEAD LATHES ::
|
|
- CLAUSING/COLCHESTER geared head lathes have earned their position as the standard of the industry, offering performance and quality at a reasonable cost. The new geared head lathes extends that reputation with new models designed to give you increased productivity into the 21st century.
- Like all Clausing/Colchester lathes the new geared head lathes are guaranteed to turn within .0001". But, beyond the accuracy you expect from Clausing/Colchester, the new geared head lathes are built rugged for durability and long-lasting quality.
|
|
|
- All head stock gears are ground and hardened
- Spindle bearings, gears, and shafts are lubricated by a pumped bath of oil
- An easy-to-read index plate makes it simple to select the proper feed or thread
- The apron has hardened gears and oil bath lubrication
- Extra wide bed provides accuracy and minimal wear
- Easy access pull-out rolling chip bin
- Precision Gamet spindle bearings
- Backed by the Clausing Service Center, the industry leader
- Equipped with chuck guard and lead screw cover
- Maximum Spindle T.I.R. .0001"
|
| |
| |
15" x 50" |
18" x 60" |
18" x 80" |
21" x 80" |
21" x 120" |
| Swing over bed |
15.7" |
18.1" |
18.1" |
21.8" |
21.8" |
| Swing over cross |
9.7" |
10.6" |
10.6" |
14.5" |
14.5" |
| Center distance |
50" |
60" |
80" |
80" |
120" |
| Bed width |
12.5" |
15.7" |
15.7" |
15.7" |
15.7" |
| Swing in gap |
23" |
28.7" |
28.7" |
32.7" |
32.7" |
| Headstock |
| Spindle nose |
D1-6 |
D1-8 |
D1-8 |
D1-11 |
D1-11 |
| Spindle through hole |
2.125 |
3 |
3 |
3.5 |
3.5 |
| Spindle speed (RPM) |
25-2000 |
20-1600 |
20-1600 |
18-1400 |
18-1400 |
| Number of speeds |
16 |
16 |
16 |
16 |
16 |
| Spindle center |
4MT |
5MT |
5MT |
5MT |
5MT |
| Feed and Threading |
| Longitudinal feed range |
.0007"-.048" |
.0016"-.11" |
.0016"-.11" |
.0016"-.11" |
.0016"-.11" |
| Cross feed range |
.00035"-.024" |
.0009"-.05" |
.0009"-.05" |
.0009"-.05" |
.0009"-.05" |
| Range of English threads |
2-56 TPI |
2-84 TPI |
2-84 TPI |
2-84 TPI |
2-84 TPI |
| Number of English threads |
56 |
73 |
73 |
73 |
73 |
| Range of Metric threads |
.2-14 mm |
.2-14 mm |
.2-14 mm |
.2-14 mm |
.2-14 mm |
| Number of Metric threads |
51 |
51 |
51 |
51 |
51 |
| Leadscrew diameter |
1.25" - 4 TPI |
1.5" - 4 TPI |
1.5" - 4 TPI |
1.5" - 4 TPI |
1.5" - 4 TPI |
| Carriage |
| Cross slide travel |
9.8" |
11.8" |
11.8" |
11.8" |
11.8" |
| Compound rest travel |
5.1" |
7.5" |
7.5" |
7.5" |
7.5" |
| Power rapid traverse |
|
Std |
Std |
Std |
Std |
| Tailstock quill diameter |
2.8" |
3.7" |
3.7" |
3.7" |
3.7" |
| Center |
5 MT |
6 MT |
6 MT |
6 MT |
6 MT |
| Quill travel |
6.1" |
5.7" |
5.7" |
5.7" |
5.7" |
| Drive motor |
10 Hp |
15 Hp |
15 Hp |
15 Hp |
15 Hp |
| Weight |
3300 lbs. |
5765 lbs. |
6170 lbs. |
6283 lbs. |
7960 lbs. |
Note1
Note2
this is where additional content would go if it was needed --
perhaps a small discription of the information provided on this page.
